Installing shower rod into ceramic tile




















A shower curtain liner is a simple vinyl or plastic curtain that goes inside the tub to prevent water from splashing all over the floor. It is usually transparent and thin so one can easily see through it from outside the tub. A shower curtain, on the other hand, hangs outside of the tub.

Barclay L-Corner Shower Rod. Locate the point where the two sections of the tension rod fit together. Tension rods have two interlocking shafts with a strong spring inside. Place one hand on either side of the spot where the rods connect and twist counterclockwise to lengthen the tension rod or clockwise to shorten it.

Standard Shower Curtain Measurements 70 x 70 inches. Tension Rods Measure the distance between the two walls where the shower rod must be mounted with a tape measure. Unscrew the rod by turning each end in an opposite direction so the rod opens or extends. Hold the shower curtain against one wall directly above the tub's apron or exposed edge as a guide.

Hold the rod in place with the curtain about an inch off the floor, then twist the smaller rod counterclockwise to lengthen it. Keep twisting after both ends have made contact with the walls until the rod has enough tension to stay in place.

For best fit, shower curtain should be 6" - 12" wider than shower rod. Mount rod approximately 3" inside the point a straight rod is normally mounted.

The midpoint of the rod should extend several inches past the outside rim of the tub. Depending upon tub model, mount rod between 6" and 8" from center line of the tub.

While most tension shower rods are rustproof and generally secure, you should keep an eye out for one that is strong enough to hold up the weight of your specific shower curtain.

Some bath tubs lend themselves to a curved shower rod whereas others work best with a standard straight design. Slide the tension rod between the 2 walls and let it expand.

Slide it into the space between your 2 walls, then loosen your hold on the rod so that it can expand. The spring inside the rod will push the ends away from each other. Put the tip of the drill bit contrary to the Whole mounting markers onto the wall or even the masking tape. The masking tape retains the end of the bit from slipping onto the ceramic tile. Push the drill bit through each mounting hole marker. A carbide-tipped masonry piece is the best drill bit to utilize for ceramic toilet tile.

Regular twist-drill pieces cannot cut through the fire-hardened glaze. Hang the shower curtain pole at an angle, with one conclusion A few inches higher than you need it. Gradually slide down that end until the pole is hanging right. The felt pads keep it from slipping down the tile wall.

Showers with sidewalls have a slight lip-shaped by the border of the bathtub sidewall along with your toilet wall. It mounts into the toilet wall, about 1 inch over this sidewall. A curved shower rod can be a simple way to add a bit of luxury to your bathroom when enhancing your shower experience.

The additional space on your shower may make it far more comfortable to use. However, you are going to be sacrificing some toilet space. Straight rods continue to be quite popular, however. A curved shower rod should be mounted around 3 inches closer to the contrary shower wall than mounts for a standard pole. Tiled walls are interchangeable with showers, but if you do not have a shower or are showering above a tub, then setting a conventional shower curtain pole can harm your tiles.

Tension-mounted shower curtain sticks offer a speedy and effective solution having a no-tool setup. We hope how to install shower curtain rod into ceramic tile article helped you out.

Setup is complete in minutes, and your shower transformed. No more cleaning up splashes and puddles off your flooring; take a Simple choice and buy a tension-mounted shower pole for your tiled bathtub.

Save my name, email, and website in this browser for the next time I comment. Even if the fastener could drill through the glazed surface, the penetrating portion of. Some brackets come in 2 separate parts: How to drill into tile to hang a shower curtain chris ceiling mount bracket wardrobe pipe bracket 25mm dia shower curtain closet wardrobe rod lever, shower curtain rod flange.

Clean both the ends of rod and wall area with rubbing alcohol; If you are a little more anxious about diy stuff then i recommend cutting your teeth on a smaller tile project. Then slide the cover in place to cover up the screw brackets. And notice how i measured so that the rod would hang just inside the tile. How to drill into tile hang a shower curtain chris loves julia.

Screw your hooks into the wall mounts. Coming Soon Shower rod, Wall tiles, Modern bathroom design. L shaped shower curtain rod White subway tile Master. Thickening stainless steel curved shower curtain rod. Measure off and mark that distance on each side of your shower with a measuring tape, subtracting 3 inches to for the drop caused by shower hooks for a shower stall. Position the shower rod with the attached mounting brackets against the bathroom wall at the points you marked.

Slide the ends of the shower rod up and down to adjust its height and position to ensure your rod is level. Cover the mounting location on the wall with masking tape if you intend to mount the rod on ceramic tile. Reposition the shower rod and mark the mounting bracket screw holes on the wall.



0コメント

  • 1000 / 1000